Adam Booth on Instagram: "Broaching the second 3/8” keyway 180° out and showing a little more of the ole Kent-Moore electric screw press. This old machine has broached countless keyways for our shop over the past 50+ years. Before that it was used at Pensacola Buggy Works. A friend of my Dad’s pulled it out of the scrap pile in the early 70’s and gave it to Dad. He then installed the electric motor, pulleys and Dayton directional switch to run the screw. Fun fact: Did you know that Doc Brown use
2:02
Adam Booth on Instagram: "Broaching the second 3/8” keywa…
31.5K views2 months ago
Instagramabom79
Adam Booth on Instagram: "Starting the Monday fresh with a machine cleanout and back into production 👏🏼 #abom79 #manufacturing #milltronics"
0:47
Adam Booth on Instagram: "Starting the Monday fresh with a machine …
23.8K views4 months ago
Instagramabom79
Adam Booth | Doing some manual labor on the Harley belt drive project ⚙️ I’m adding a spot face for each of the new 16 through holes for proper flange... | Instagram
2:56
Adam Booth | Doing some manual labor on the Harley belt drive proj…
21.9K views3 months ago
Instagramabom79
Adam Booth on Instagram: "It’s time to haul the aluminum chips to the scrap yard again so we’ll give the @airtowtrailers an easy workout with this load 😎 The ground level loading capabilities are so nice! #abom79 #airtow #airtowtrailers"
1:28
Adam Booth on Instagram: "It’s time to haul the aluminum chips to the …
17.2K views3 months ago
Instagramabom79
Adam Booth on Instagram: "Finishing off the winch drum’s two new drilled & tapped holes. #abom79 #manualmachining #industrialrepair #machineshop #greenfieldcuts"
2:09
Adam Booth on Instagram: "Finishing off the winch drum’s tw…
11.2K views2 months ago
Instagramabom79
Adam Booth on Instagram: "Pump shaft shortened & threaded 1-1/2-8 left hand. Full detailed video coming to the youtube channel soon. MX22 threading tool by @waltertools #abom79 #singlepointthreading #industrialrepair #machineshop #manualmachining"
2:24
Adam Booth on Instagram: "Pump shaft shortened & threaded 1-1/2-…
44.2K views2 months ago
Instagramabom79
Adam Booth on Instagram: "Another stuck winch drum shaft. Before we set it in the 50 ton press we’re going to help out with some heat and Knock’er Loose penetrant. We literally just brought the torch set to the new shop space but the press is still at the old home shop. I’m hoping that all of the preliminary work will help to break the corrosive bond. Find out what happens in this weekends YouTube video. #abom79 #industrialrepair #press #knockerloose #crcauto"
2:18
Adam Booth on Instagram: "Another stuck winch drum shaft. Before w…
67.7K views2 months ago
Instagramabom79
1:21
Adam Booth | I used a 1/2” Helical chip splitter to open up the holes t…
8.9K views4 months ago
Instagramabom79
2:52
Adam Booth | Counterboring the second hole pattern and milling fl…
40.2K views3 months ago
Instagramabom79
Adam Booth | We’re excited to announce that our purple anodize…
1 month ago
Instagram
1:44
Adam & Abby Booth on Instagram: "Well crap. It happens! We were b…
583.7K views5 months ago
Instagramabomadventures
1:24
Adam Booth | We’ve had our Kubotas in storage for 4 years no…
8.3K views4 months ago
Instagramabom79
1:14
Adam Booth on Instagram: "Taking the 1/4” hat off of for Op2 in this st…
26.4K views3 months ago
Instagramabom79
2:29
Adam Booth on Instagram: "I got my big offset smoker moved this wee…
17.3K views2 months ago
Instagramabom79
#abom79 #milltronics #autodeskfusion #cncmachining | …
1 views4 weeks ago
linkedin.com
#abom79 #milltronics #autodeskfusion #cnclathe #cncm…
1 views1 month ago
linkedin.com
Adam Booth | Rush job for the airport to help get the luggage equ…
6 months ago
Instagram
Adam Booth on Instagram: "Damaged thread repair in a Brem…
1.9M viewsJan 11, 2025
Instagramabom79
Adam Booth on Instagram: "Satisfying broken & seized bolt r…
15.4M viewsJan 14, 2025
Instagramabom79
5:38
Abom Adventures Introduction
34.2K viewsSep 16, 2017
YouTubeAbom Adventures
28:53
Machine Shop Tours: Abom79
118.5K viewsDec 2, 2020
YouTubePractical Machinist
5:37
MiHow2 - Motion Industries - Hydraulic Cylinder Repair with Ad…
43.5K viewsJan 21, 2016
YouTubeMotion
42:33
Gear Cutting Basics and Cutting Pinion Gears on a Horizontal Mill
550K viewsJul 10, 2015
YouTubeKeith Rucker - VintageMachinery.org
0:59
Adam Booth on Instagram: "Machining a 1/4” radius on some …
156K viewsDec 10, 2021
Instagramabom79
2:22
Adam Booth | Here’s the follow up video showing the drilling, boring …
56.6K viewsJun 22, 2022
Instagramabom79
0:52
Adam Booth | I’m using the Vortex drill for the first time on some 114…
39.7K viewsAug 19, 2021
Instagramabom79
21:03
20MM Driveshafts
101K viewsSep 24, 2022
YouTubeAbom79
22:59
Machining the American Flag
58.1K viewsSep 2, 2023
YouTubeAbom79
2:26
Big Changes Ahead
94.5K viewsJan 18, 2019
YouTubeAbom79
1:02:00
Abom79 Podcast Episode 1
26.3K views8 months ago
YouTubeAbom79
See more videos
Static thumbnail place holder